As you know, there are thousands of Bluetooth and WiFi signals we pass through daily, especially if we live an active life in a big city. That includes tags, smartphones, WiFi routers, drones, surveillance devices, vehicles, body cams and mesh radios. Clearly it doesn’t stop here and the list goes on.
Many of you are privacy focused individuals and want to know what’s going on around you and whether you’re being tracked or watched by someone. That’s okay, protecting your privacy is a good thing. FieldWatch was made for this. It matches what it hears against an editable signature catalog of roughly 250 device types and shows the results in live views, recorded sessions, path maps and reports. Everything runs on the device and works fully offline.
FieldWatch
FieldWatch is a free, open-source Android app that listens to nearby Wi-Fi and Bluetooth signals using the radios already in your phone. It compares what it hears against a list of known device signatures and shows them. It only receives signals. It never transmits.
Source: OGridPeteSource: OGridPete
You can set alerts for specific devices, record what’s present during a walk or drive, and later compare sessions. All the findings are sorted under their category. It also has basic GNSS interference detection and can send results to mapping tools like TAK. Matches are based on patterns, not guaranteed identifications, and the app only sees what the phone’s radios and Android allow it to see.
Depending on your preferences, you may want to see these devices on a radar or on a map. The app found the location of the drone operator as well as the drone itself.
Source: OGridPeteSource: OGridPete
TAK Support
TAK and ATAK are free mapping apps used by military, emergency responders and some civilians to share locations and information on a map in real time. FieldWatch can send what it detects straight to TAK over the local network.
When FieldWatch sees a drone that’s broadcasting Remote ID, it can place a moving marker on the TAK map for the drone and a second marker for the pilot if that location is available. Other devices it finds, plus any GNSS interference alerts, can also appear as markers. Several phones running FieldWatch can send data to the same map at the same time, so a team sees the same picture.
Source: OGridPete
GNSS Interference Detection
Newer versions check for signs of GPS interference or spoofing using the phone’s own receiver. After a short outdoor calibration, it can alert you and mark the spot on your path or on a TAK map. It shows where you were, not where the interference came from.
Source: OGridPete
Limits
Now let’s talk about its limits. It isn’t a direction finder. Also, it doesn’t scan Bluetooth Classic, cellular networks or full Wi-Fi traffic. Matches are based on patterns and those are not confirmed identities. Your results depend on the phone and what Android lets the app see. For better results use newer phones. Official versions only come from the GitHub repo.
Android App
Download the APK from the official GitHub page and sideload it. Android 10 or newer is required. Android 11 has more functions that can be used with this app. A short instruction file and manual are included. The repository has all the answers in terms of the app. It works on a cheap phone with no SIM card. OffGridPete recently posted that he used a Moto G for $30 for his test and it worked well. If you decide to use it, use it for your own privacy and security, and be respectful of other people’s privacy.
Summary
You can use your cheap phone as a scanner for devices nearby, and find jamming and tracking. There are different apps that do similar things, but they’re bound to Linux only, which is very inconvenient. FieldWatch works on an Android phone to find trackers, cameras, drones, body cams and more.
If you enjoy experimenting with frequencies and trying new things, we recommend signing up for our SDR for Hackers training. With Master OTW, you’ll learn how to use your computer and inexpensive SDR hardware to explore and hack a wide range of radio signals.
Many beginners want to know how they can hack their Wi-Fi. It’s fun, it’s easy to get started with and those small wins make the early part of your cybersecurity journey exciting. Testing Wi-Fi security is also an important part of a pentest, since many organizations keep old routers in place with weak security settings. As years go by, those settings get more and more obsolete, like WEP. Some features routers have enabled by default might be convenient, but are often unnecessary. That’s WPS, as you might know. It gets abused regularly to recover a plaintext password and sometimes you can get it in under a minute just because WPS was left on.
If hackers get onto the network, they can start exploring everything on it or just use your Wi-Fi for their own purposes. You don’t want that. That’s why you need to make sure it’s secure.
Today we’ll cover Wifit3, which can help you with this.
What is Wifit3
The tool was developed by the same author who created Wifite2.
Unlike its predecessor, it doesn’t need aircrack-ng, reaver or bully installed. Instead, it uses pure Python with the PyUSB and Textual libraries. Wifit3 works just as well on Linux, macOS and Windows. You’ll only need a USB dongle to work with it. The repository mentions all the supported devices.
It scans both 2.4 GHz and 5 GHz, can tell when a network is WPA3 or in mixed WPA2/WPA3 mode and keeps track of signal and encryption. It also tries to identify the router and pull extra details about it. Hidden network names sometimes get revealed by matching them to a known router address. If you plug in more than one supported Wi‑Fi adapter, you can listen on several at once and leave one free to send packets.
It shows beacons, data, injection and disconnect traffic so you can see what’s in the air while you work.
The tool can listen to Wi‑Fi traffic and send disconnect messages. Those messages kick phones off the network. When a phone joins again, it talks to the router to prove it knows the password. The tool records that conversation. The password is in there, but scrambled, so you can crack it later with hashcat.
Here’s how it looks. Above you can see it capturing handshakes with passwords after disconnecting a client. The tool also managed to capture a PMKID. PMKID is a short hash the router can send that’s tied to the Wi-Fi password. If you capture that hash, you can try passwords against it later on your own machine. You don’t need to kick anyone off the network or capture a full login handshake.
There’s also an Evil Twin mode for WPA3. It tricks phones into leaving the real Wi‑Fi and joining a fake one so the tool can steal a handshake. For WPS it can try the fast Pixie Dust attack, grab the password when someone presses the router’s WPS button and keep guessing the WPS PIN while pausing if the router starts locking out attempts.
That’s how the WPS attack looks. The tool sends an enrollee identity with a public key and gets the router credentials decrypted. The password is then saved to a text file.
WEP is attacked in Python with the usual replay tricks to recover the key.
Setting Up
Now let’s set it up on our machine. As always, we’re going to use Kali, but you can use anything you want.
kali > wget https://github.com/derv82/wifit3/releases/download/v0.3.2/wifit3-linux-x64 -q
kali > chmod 777 wifit3-linux-x64
kali > mv wifit3-linux-x64 wifit3
kali > sudo cp wifit3 /usr/local/bin
We’re all set. Plug in your USB dongle and start the tool.
kali > wifit3
After choosing the right, you can start testing your Wi-Fi. Use it only on your own Wi-Fi or the one you’re authorized to test.
Summary
There are so many vulnerable Wi-Fi networks you’ll come across during pentests. They’re often the quickest way into a network, which is why their security shouldn’t be overlooked. Wifit3 is a new tool that came out relatively recently. It’s easy to work with and can help you cover all the common wireless attacks.
If you’re interested in Wi-Fi security, our Wi-Fi Hacking training can help you gain the necessary experience.
A while back, we walked you through building your own hacking drone. It was a drone loaded up with tools designed to help you out during an actual pentest. That was a hands-on project in every sense of the word. If you built one, you probably learned a ton just from putting the hardware together.
This time, we’re doing something different. No soldering iron. We’re staying entirely inside your laptop working with the Damn Vulnerable Drone, which is an open-source simulator built for teaching you exactly how drones get hacked, without you ever touching a real drone.
The Damn Vulnerable Drone
The Damn Vulnerable Drone, or DVD, is a training simulator that was made for people who want to learn drone hacking without buying a drone. It recreates an entire drone system in software, including a flight controller, an onboard companion computer, a ground control station and the wireless links connecting them all. Every piece is there, and every piece runs inside Docker containers on a single computer.
The project was built by Nicholas Aleks, a security researcher and co-founder of DEF CON Toronto, and it’s aimed squarely at intermediate-level red teamers and hacking enthusiasts who want to practice with actual drone protocols and architecture. Drone hardware and radios are genuinely expensive, and a mistake on a real flight controller can be costly. You get to make your mistakes safely, over and over, until you actually understand what you’re doing. DVD runs actual ArduPilot firmware as an ordinary program and pairs ArduPilot’s SITL with Gazebo, which is a 3D robotics simulator that supplies realistic physics. Motors spin up, GPS signals drift the way they really do, and the drone actually flies through a rendered 3D world.
Under the Hood
Every Docker container gets its own address on an internal network. That’s a design choice that mirrors how a real drone’s components actually work. The first piece is the Flight Controller, which runs the ArduPilot firmware itself and talks directly to the Gazebo simulator to process virtual sensor data. The second piece is the Companion Computer, which handles Wi-Fi, camera streaming, telemetry logging, and autonomous navigation, and which also exposes its own web interface for you to interact with. The third piece is the Ground Control Station, the pilot’s side of the operation, covering mission planning, mapping, video, and joystick control, all communicating over a simulated wireless MAVLink link. And the fourth piece is the Simulator itself, the Gazebo container that models flight physics behind the scenes. The documentation specifically tells you not to attack this fourth container directly, because doing so can crash the entire lab out from under you. Everything else is fair game. That one, leave alone.
Getting Started
To install it we need to pull down containers. The project offers two configurations based on whether you have a dedicated graphics card.
If the answer is no, you need Lite Mode. It uses a simplified 2D flight model, needs no GPU at all, and runs comfortably on 4 to 8 GB of RAM, 2 CPU cores, and about 100 GB of disk space. It works on Kali Linux or most other Linux distributions, and you can run it either on bare metal or inside a virtual machine. If the answer is yes, Full Mode gives you the complete Gazebo 3D environment, but it asks more of your machine in return. You need 8 to 16 GB of RAM, 2 to 4 CPU cores, 100 GB of disk space, and a GPU with at least 2 GB of VRAM supporting OpenGL 3.0 or newer. Full Mode is Kali Linux only, and it strongly prefers bare metal, though a virtual machine with GPU passthrough will also work.
Kali Linux is the officially supported operating system either way, and both modes need Docker and Docker Compose installed as the only real software dependency you have to worry about. Once Docker is installed, the whole lab comes up with a handful of commands.
First, if Docker isn’t already on your system, you’ll want to install it:
kali > printf '%s\n' "deb https://download.docker.com/linux/debian bullseye stable" | sudo tee /etc/apt/sources.list.d/docker-ce.list
kali > curl -fsSL https://download.docker.com/linux/debian/gpg | sudo gpg --dearmor -o /etc/apt/trusted.gpg.d/docker-ce-archive-keyring.gpg
kali > sudo apt update -y
kali > sudo apt install docker-ce docker-ce-cli containerd.io -y
kali > sudo systemctl enable docker --now
kali > sudo usermod -aG docker $USER && newgrp docker
Then, clone the repository and pull down the containers. If you’re going with Lite Mode, do this:
kali > git clone https://github.com/nicholasaleks/Damn-Vulnerable-Drone.git && cd Damn-Vulnerable-Drone
kali > docker compose -f docker-compose-lite.yaml pull
From there, three small scripts manage the whole lab’s lifecycle for you:
kali > sudo ./start.sh --mode lite --Wi-Fi wpa2
kali > sudo ./status.sh
kali > sudo ./stop.sh
The start.sh script alone has quite a few options worth knowing about. The –mode full or –mode lite flag picks your simulation type, matching the two modes described above. And the –Wi-Fi wep or –Wi-Fi wpa2 flag is optional, but it’s worth turning on, because it spins up a virtual wireless network alongside everything else. That means your practice can actually include real Wi-Fi attacks as the very first step, instead of starting the exercise with network access already handed to you.
Interface and Feedback
Once everything is up and running, DVD is controlled through a browser-based management console sitting at localhost:8000
This console is really where the whole exercise plays out. A set of buttons trigger five distinct flight states: Initial Boot, Arm & Takeoff, Autopilot Flight, Emergency/Return-to-Land, and Post-Flight Data Processing. Each one simulates a different phase of a drone’s mission and opens up a different attack surface for you to explore. Triggering “Arm & Takeoff,” for instance, actually gets the simulated drone airborne, which gives GPS and navigation-based attacks something real to act on.
That mapping to real flight phases is there for a reason. A drone accepts different commands, and trusts different sources of data, depending on whether it’s sitting idle on the ground, climbing out after takeoff, cruising on autopilot, or executing an emergency fail-safe. That means exercises built around each individual state end up testing different parts of the system.
The Attack Scenario Library
This is really the heart of the whole project. It has more than 40 named attack scenarios, organized into six categories, each one with its own documentation page and a spoiler-tagged walkthrough waiting behind it. It’s a deliberately broad menu, and it’s worth noticing that some scenarios are about gathering information without being noticed, while others are about actively manipulating or outright breaking the system in front of you.
Reconnaissance scenarios are about passively fingerprinting the drone, its companion computer, and its ground station by watching Wi-Fi and MAVLink traffic go by, without touching anything yet. Protocol Tampering scenarios involve spoofing telemetry values the drone reports, things like its GPS position, battery level, or system status, to see whether the system properly checks what it’s being told. Denial of Service scenarios focus on disrupting flight through methods like Wi-Fi deauthentication or flooding the communication link until it can’t keep up. Injection scenarios involve sending forged commands directly into the MAVLink stream, ranging all the way from a simple waypoint change to a full companion-computer takeover. Exfiltration scenarios are about pulling data off the drone entirely, whether that’s flight logs, mission plans, or content from the camera feed. And Firmware Attacks focus on modifying or reverse-engineering the ArduPilot firmware itself, right down at the code level.
Battery Spoofing
Because every scenario runs against fully simulated components, you actually get to see the complete effect of an attack play out. A spoofed GPS reading really does nudge the simulated flight path off course. A flooded communication link really does degrade control, right in front of you. And you get to watch all of it happen without any of the legal or physical risk that would come with testing the same techniques on live hardware.
Wi-Fi and Non-Wi-Fi Modes
DVD can be deployed in two different ways, and which one you pick depends on which part of the attack chain you actually want to practice. Wi-Fi Mode spins up a real, functioning virtual wireless network, broadcasting an SSID called Drone_Wi-Fi on the 192.168.13.0/24 range, with your choice of weak WEP encryption or the considerably stronger WPA2. This lets the whole exercise start from the very beginning, with you playing the role of an attacker who doesn’t have network access yet and has to earn it.
Non-Wi-Fi Mode skips that entire step and simply brings the containers up directly. This is useful if you just want to focus purely on protocol-level attacks, or if you’re not running inside a Kali VM with wireless card support to begin with. In this mode, the documentation asks you to treat the situation as though initial access to the drone’s data link has already been established, so you can jump straight to the MAVLink-level work.
Summary
The Damn Vulnerable Drone takes an idea that’s already well proven in web security and applies it to a domain where practicing on the real thing tends to be expensive. By simulating a full ArduPilot and MAVLink drone stack inside Docker, right down to Wi-Fi, camera streaming, and flight physics, it hands penetration testers, students, and researchers a realistic, disposable target, backed by more than 40 documented attack scenarios and built-in walkthroughs to guide the way. It won’t teach you to fly a real drone. But it will teach you exactly how one can be hacked, and for anyone working in drone security, that’s the more useful skill anyway.
If you’re interested in drone hacking, check out our Building Your Own Hacking Drone series, where we walk you through attack scenarios targeting Bluetooth and Wi-Fi across a wide range of devices.
We also offer a Drone Hacking training course, taking place November 10-12 at 4:00 PM UTC, available to Subscriber and Subscriber Pro students.
Take a second and think about how many devices are actually working around you right now. Cameras on street corners, routers sitting inside nearby homes, Bluetooth earbuds in someone’s pocket, cell towers just outside of view. All of that is happening constantly, yet almost none of it is visible to the average person walking by. If you actually wanted to check what devices were nearby today, you would probably end up jumping from one app to another, waiting for each one to load, and still walking away without the full picture. It is slow, it is frustrating, and honestly, it takes all the fun out of exploring what is really going on around you.
A lot of these devices are not just sitting there minding their own business. Many of them are built specifically to track you. A recent video on X showed this. It captured a flock camera taking several pictures of a moving vehicle, running those pictures through some kind of analysis, and then filing everything away in an indexed format.
In the screenshot above, you can see the guy picking up the signal coming straight off the camera, while the camera itself keeps emitting a steady beam of infrared. Here is the full video.
Privacy is not a crime, and you have every right to know what might be watching you. The real challenge has always been figuring out where all of these surveillance devices are hiding. That’s where WireTapper can help us. It pulls data from Wigle, Shodan, and OpenCelliD one at a time. That way, you can see every one of these devices in your area.
WireTapper
WireTapper is a wireless OSINT tool designed to discover, map, and analyze radio based devices using passive signal intelligence. WireTapper detects and correlates signals coming from all the common wireless technologies you would expect to run into. This helps you understand what devices actually exist nearby and where they are likely located all without ever having to actively intrude on anything.
WireTapper can identify leaked Wi-Fi network credentials, and it does this through a privacy-protecting k-Anonymity query scheme, meaning it can check for exposed passwords without ever exposing your own search to the outside world.
Setting Up
Let’s quickly walk through the installation process. It’s a lot simpler than it looks.
kali > git clone https://github.com/h9zdev/WireTapper.git
kali > cd WireTapper
kali > python3 -m venv venv; source venv/bin/activate
kali > pip3 install -r WireTapper.txt
Once that finishes, you will need to grab API keys from each of the services mentioned above. Do not worry too much about Shodan, since its API is paid and WireTapper will still run fine without it. There are two ways to plug these keys into the app. You can either open app.py and enter them directly, or you can use app-env.py instead, which pulls the keys in through environment variables.
After you have picked your method, we recommend also installing python-dotenv, since it makes handling those environment variables a lot smoother.
kali > pip3 install python-dotenv
Working with WireTapper
Once everything is installed, you are ready to start the app and open the web interface.
kali > python3 app.py
The web interface will be waiting for you right here: http://localhost:8080/map-w
This is the dashboard you will land on the moment you open the page. It takes a little while to load everything, so give it a few minutes before you start clicking around. Once it settles in, you can zoom into whatever area you are curious about and start picking apart what is actually hiding there.
Just keep in mind that you need valid API keys for the app to work the way it is meant to. Without them, WireTapper will simply generate dummy data so you can still see how everything normally looks inside it. On Wigle specifically, your email needs to be verified before the connection will work properly.
At the top of the dashboard, you will notice a switch that lets you jump between Wi-Fi uplink and Bluetooth scanners. That is how you filter what you are looking at.
Flip the switch back the other way, and you get the same kind of view but for Wi-Fi devices instead. This side usually includes things like cameras, routers, and other similar devices.
Exporting Results
All of these results can be exported complete with their names and coordinates, in case you decide to use them somewhere else later on.
The example above is just a taste of how those exported results are going to look. You can use this JSON file with other tools.
Summary
There is far more happening around us than most people realize. WireTapper makes it easier to visualize that activity by bringing together information about nearby wireless infrastructure in one interface. If you’re into OSINT, privacy, or wireless security, it’s a handy tool.
OSINT is a valuable skill in many areas, especially when it comes to privacy, cybersecurity, and cyber warfare. The more you understand what information is publicly exposed, the better you can protect yourself and your digital assets. Our Ultimate OSINT Beginner training covers OPSEC, tracking, investigations, and much more across 23 lessons and 7.5 hours of video content.
We’re also hosting a live Remaining Anonymous training on August 11-13 at 3:00 PM UTC for all Subscriber and Subscriber Pro students.
Login
